硅PU球場施工要點基面處理先清潔施工面，然后用清水濕潤基面，用5%左右的稀鹽酸潑灑并洗刷水泥基面。如有水磨機，對整個場地進行打磨處理為比較好方案）再用清水沖洗干凈。觀察存留水跡，對基面進行平整度和坡度的檢驗，用記號筆圈劃出積水處。清洗干燥后基面應無白色粉化物及浮塵物。伸縮縫處理對水泥混凝土基礎縫隙處都須開V字口。在填縫前要先將混凝土伸縮縫清潔干凈，并打上一遍防水底漆。如縫較深或較寬的可用橡膠顆粒先作一個墊底，然后再填充；對部分特別凹陷部位可用硅PU彈性材加無機材料進行修補。室外球場施工，膜結構施工，上海雙步實業。楊浦區球場施工價格

硅PU球場防水底涂1）基層干燥后，對明顯凸出部分進行打磨處理，然后施工封閉底漆。施工時水泥基面要求堅固、干燥、干凈、平整，無油污及粉化現象。2）必須待基礎干燥透徹后用滾筒將底漆材料均勻地滾涂在水泥基面上，起到封閉水泥基面的隙孔，提高塑膠層與水泥基面的粘結強度的作用，使之不易脫層和產生氣泡。如有部分地面吸料較明顯的要重復滾涂一至兩遍。待底漆層干固后，再進行下一道工序施工。彈性層施工在施工該涂層前檢查確認基礎處理符合施工要求，刮涂的遍硅PU彈性材不得加水，刮涂厚度1-1.5mm以內，如局部因過厚出現鼓小泡屬正常情況。彈性層施工是采用薄涂多遍的方法施工。施工時用帶齒鏝刀將硅PU彈性材涂刮于基面上，每道涂刮厚度不超過1.5mm，直至涂刮到要求厚度。每道涂刮時間間隔為前一道干固為準。涂刮時注意流平效果，若不能流平刮齒痕跡，需添加環保流平劑調節粘稠度，以保證表面流平。遍硅PU層干固后，用積水法測試表面平整度，積水處用硅PU彈性材料加石英砂修補平整，表面有粒狀雜物混入或堆積處需用磨機打磨平整再進行下一道工序施工。長寧區學校球場施工包工包料羽毛球場翻新施工材料 上海雙步實業。

硅PU球場施工彈性層用帶齒鏝刀將緩沖層材料涂刮于基面上2道，每道涂刮時間間隔以前一道干固為準（一般約10小時）。彈性層施工前應仔細檢查確認基礎處理完后方能進行彈性層施工，用稀釋劑調節合適施工稠度，用硅PU耙子均勻的涂于基面。每道涂刮時間間隔以前一道干固為準（一般約10小時，具體視現場天氣情況而定，適當增減催化劑含量）直至涂刮至所需厚度。涂刮時注意流平效果，若不能流平刮齒痕跡，需多加稀釋劑以保證表面流平。避免在猛烈陽光照射下施工。彈性層干固后，用積水法測試表面平整度。積水處用彈性層修補平整，表面若有粒狀雜物或堆積處需用磨機或其它工具修整平后才能進行加強層施工。上海雙步實業有限公司

面層攤鋪用EPDM顆粒和**膠水按4：1重量配比，用攪拌器械在攪拌區攪拌均勻，用送料車送到預先劃好界線處，用刮尺攤鋪，用滾碾子壓實(在條件和面積適合的情況下，可以使用專業攤鋪機攤鋪)，要注意密實度，平整度、厚度，反復滾壓。經過二至三小時的固化，再次用滾碾子壓實，不平整的地方用鏝刀拍打平整，如鏝刀、滾碾子粘顆粒，沾少許稀釋劑起到光滑的作用。

標志線的測劃按照圖紙設計籃球場尺寸進行測量，劃出球場標志線。正確使用經緯儀，鋼卷尺等測量工具，按標準測量確定各種標志線的位置，反復測量，校核確認無誤以達要求的精確度，方可用記號筆(特種鉛筆)在面層上劃線做記號。劃線后需經體育工藝員復核。直線部分用鑒定過的鋼卷尺(包括尺長校正、溫度校正)進行復核，確認符合標準后，方可按規定的標志噴漆。噴漆時，要反復檢查標志線寬度是否符合規定，如不符合應及時調整。

籃球場施工找上海雙步實業免費設計。

丙烯酸網球場底層的刮涂

將調配好的底料（稍稠）倒于地上，用2-3米的長的鋁合金方刮涂一遍（低洼處補平）爆曬：由于次刮涂的底料較厚（視基礎平整情況，如果基礎不平，局部就會很厚），因此這一層底層一定要給徹底干燥到底，不能只看到表面干燥，具體干燥時間視天氣情況而定。如局部太厚干燥時間過長，可用太陽燈烤，加快它的干燥時間。試水：待次底料完全干燥后,全場放水,在水不流動時,在有積水的地方作出標記.修補積水：（根椐場地排水系統來定）采用鋁合金方在積水的地方用底料刮平，達到修補積水的目的。重復，步，達到場地無積水為止。鏟地：將修補和刮涂底料產生的耙痕和凸出部分徹底鏟平或用打磨機磨平并清掃干凈地面。第二次底料：沿球場縱向的方向刮涂一次底料（待干）第三次底料：在第二次底料完全干燥后可沿球場橫向刮涂第三次底料（待干）。一次試水和修補：第三次底料完成后，重新試水，檢測是否有積水，如有就重復，步，達到場地無積水為止。籃球場施工，球場材料硅PU。普陀區羽毛球球場施工

籃球場施工，運動木地板籃球場。楊浦區球場施工價格

硅PU球場面漆施工面漆為水性環保材料，必須按規定比例把水性面漆+水性面漆固化劑（15:1）充分攪拌均勻，用膠刮板分2～3道刮涂于加強層表面。表面需粗糙的可以加入≤30%面層砂，應先將A組份與砂攪拌均勻再加入B組充分混合均勻后刮涂。（各類球場面層參考做法：乒乓球、籃球場：道加入30%砂，第二道加入15%砂，第三道不加砂；網球場：加入30%砂分2～3道刮涂。羽毛球、排球場：不加砂分2～3道刮涂。）面層施工用料必須足量，否則會直接影響使用效果及使用期限。應避免烈日及表面溫度過高情況下施工，保證表面效果。楊浦區球場施工價格

本文來自宜興市恒通風機有限公司：//vijoo.com.cn/Article/15f0799977.html